Publications - Dr. Yong Huang

Articles

  1. Yan, J., Huang, Y., and Chrisey, D.B., Laser-Assisted Printing of Alginate Long Tubes and Annular Constructs, Biofabrication, Vol. 5(1), pp. 015002-1-8, 2013.
  2. Xu, C., Chai, W., Huang, Y., and Markwald, R.R., Scaffold-Free Inkjet Printing of Three-Dimensional Zigzag Cellular Tubes, Biotechnology and Bioengineering, Vol. 109(12), pp. 3152Ð3160, 2012.
  3. Yan, J., Huang, Y., Xu, C., and Chrisey, D.B., Effects of Fluid Properties and Laser Fluence on Jet Formation during Laser Direct Writing of Glycerol Solution, J. of Applied Physics, Vol. 112(8), pp. 083105-1-8, 2012.
  4. Yin, J., Coutris, N., and Huang, Y., ÒNumerical Study of Axonal Outgrowth in Grooved Nerve Conduits,Ó Journal of Neural Engineering, Vol. 9(5), pp. 056001-1-12, 2012
  5. Herran, C.L., Huang, Y., and Chai, W., ÒPerformance Evaluation of Bipolar and Tripolar Excitations during Nozzle-Jetting-Based Alginate Microsphere Fabrication,Ó J. Micromech. Microeng., Vol. 22(8), pp. 085025-1-11, 2012.
  6. Zhang, D., Yang, F., Shimotori, T., Wang, K.-C., and Huang, Y., ÒPerformance Evaluation of Power Management Systems in Microbial Fuel Cell-Based Energy Harvesting Applications for Driving Small Electronic Devices,Ó Journal of Power Sources, Vol. 217, pp. 65-71, 2012.
  7. Phamduy, T.B., Raof, N.A., Schiele, N.R., Yan, Z., Corr, D.T., Huang, Y., Xie, Y., and Chrisey, D.B., ÒLaser Direct-Write of Single Microbeads into Spatially-Ordered Patterns,Ó Biofabrication, Vol. 4, pp. 025006-1-12, 2012.
  8. Yang, F., Zhang, D., Shimotori, T., Wang, K.-C., and Huang, Y., ÒStudy of Transformer-Based Power Management System and its Performance Optimization for Microbial Fuel Cells,Ó Journal of Power Sources, Vol. 205, pp. 86-92, 2012.
  9. Yin, J., Coutris, N., and Huang, Y., ÒExperimental Investigation of Aligned Groove Formation on the Inner Surface of Polyacrylonitrile Hollow Fiber Membrane,Ó Journal of Membrane Science, Vol. 394-395, pp. 57-68, 2012.
  10. Riggs, B.C., Dias, A.D., Schiele, N.R., Cristescu, R., Huang, Y., Corr, D.T., and Chrisey, D.B., ÒMatrix-Assisted Pulsed Laser Methods for Biofabrication,Ó MRS Bulletin, Vol. 36(12), pp. 1043-1050, 2011.
  11. Yin, J., and Huang, Y., ÒStudy of Process-Induced Cell Membrane Stability in Cell Direct Writing,Ó ASME J. of Manufacturing Sci. and Eng., Vol. 133(5), pp. 054501-1-5, 2011.
  12. Lin, Y., and Huang, Y., ÒLaser-Assisted Fabrication of Highly Viscous Alginate Microsphere,Ó J. of Applied Physics, Vol. 109(8), pp. 083107-1-8, 2011.
  13. Wang, X., and Huang, Y., ÒConvergence Study in Extended Kalman Filter-based Training of Recurrent Neural Networks,Ó IEEE Trans. on Neural Networks, Vol. 22(4), pp. 588-600, 2011.
  14. Wang, W., Lin, Y., and Huang, Y., ÒModeling of Thermoelastic Stress Wave in Laser-Assisted Cell Direct Writing,Ó ASME J. of Manufacturing Sci. and Eng., Vol. 133(2), pp. 024502-1-6, 2011.
  15. Huang, Y., and Morehead, M., ÒStudy of Machining-Induced Microstructure Variations of Nanostructured/Ultrafine-Grained Copper using XRD,Ó ASME J. of Engineering Materials and Technology, Vol. 133(2), pp. 021007-1-7, 2011.
  16. Lin, Y., Huang, Y., and Chrisey, D.B., ÒMetallic Foil-Assisted Laser Cell Printing,Ó ASME J. of Biomechanical Eng., Vol. 133(2), pp. 025001-1-5, 2011.
  17. Yin, J., Coutris, N., and Huang, Y., ÒGroove Formation Modeling in Fabricating Hollow Fiber Membrane for Nerve Regeneration,Ó ASME J. of Applied Mechanics, Vol. 78(1), pp. 011017-1-7, 2011.
  18. Wang, X., Huang, Y., and Nguyen, N., ÒRobustness Quantification of Recurrent Neural Network Using Unscented Transform,Ó Neurocomputing, Vol. 74, pp. 354-361, 2010
  19. Yin, J., Coutris, N., and Huang, Y., ÒRole of Marangoni Instability in Fabrication of Axially and Internally Grooved Hollow Fiber Membranes,Ó Langmuir, Vol. 26(22), pp. 16991Ð16999, 2010.
  20. Schiele, N.R., Corr, D.T., Huang, Y., Raof, N.A., Xie Y., and Chrisey, D.B., ÒLaser-based Direct-Write Techniques for Cell Printing,Ó Biofabrication, Vol. 2, pp. 032001-1-14, 2010.
  21. Lin, Y., Huang, G., Huang, Y., Tzeng, T.J., and Chrisey, D.B., ÒEffect of Laser Fluence in Laser-Assisted Direct Writing of Human Colon Cancer Cell,Ó Rapid Prototyping Journal, Vol. 16(3), pp. 202Ð208, 2010.
  22. Long, Y., Huang, Y., and Sun, X., ÒCombined Effects of Flank and Crater Wear on Cutting Force Modeling in Orthogonal Machining, Part II: Bayesian Approach-based Model Validation,Ó Machining Science and Technology: An Int. Journal, Vol. 14(1), pp. 24-42, 2010
  23. Long, Y., and Huang, Y., ÒCombined Effects of Flank and Crater Wear on Cutting Force Modeling in Orthogonal Machining, Part I: Model Development,Ó Machining Science and Technology: An Int. Journal, Vol. 14(1), pp. 1-23, 2010.
  24. Yan, Z., Bao, R., Huang, Y., Caruso, A.N., Qadri, S.B., Dinu, C.Z., and Chrisey, D.B., ÒExcimer Laser Production, Assembly, Sintering, and Fragmentation of Novel Fullerene-like Permalloy Particles in Liquid,Ó J. of Physical Chemistry C, Vol. 114, pp. 3869Ð3873, 2010.
  25. Wang, W., Huang, Y., Coutris, N., Noh, H.S., and Hesketh, P.J., ÒEvaluation of Transverse Shear Effect on Film Delamination in Blister Test,Ó ASME J. of Electronic Packaging, Vol. 132(1), pp. 014501-1-5, 2010.
  26. Wang, K.-C., Jacob, J., Tang, L., and Huang, Y., ÒTransmission Error Analysis and Avoidance for IEEE 802.15.4 Wireless Sensors on Rotating Structures,Ó Int. J. on Sensor Networks, Vol. 6(3-4), pp. 224-233, 2009.
  27. Wang, W., Li, G., and Huang, Y., ÒModeling of Bubble Expansion-Induced Cell Mechanical Profile in Laser-Assisted Cell Direct Writing,Ó ASME J. of Manufacturing Sci. and Eng., Vol. 131(5), pp. 051013-1-10, 2009.
  28. Lin, Y., Huang, Y., Wang, G., Tzeng, T.J., and Chrisey, D.B., ÒEffect of Laser Fluence on Yeast Cell Viability in Laser-Assisted Cell Transfer,Ó J. of Applied Physics, Vol. 106(4), pp. 043106-1-7, 2009. (Also in: Virtual Journal of Biological Physics Research, Vol. 18(5), September, 2009)
  29. Wang, X., and Huang, Y., ÒOptimized Recurrent Neural Network-Based Tool Wear Modeling in Hard Turning,Ó Transactions of NAMRI/SME, Vol. 37, pp. 213-220, 2009.
  30. Lin, Y., Huang, Y., and Chrisey, D.B., ÒDroplet Formation in Matrix-Assisted Pulsed-Laser Evaporation Direct Writing of Glycerol-Water Solution,Ó J. of Applied Physics, Vol. 105, pp. 093111-1-6, 2009.
  31. Tang, L., Wang, K.-C., and Huang, Y., ÒPerformance Evaluation and Reliable Implementation of Data Transmission for Wireless Sensors on Rotating Mechanical Structures,Ó Structural Health Monitoring, An International Journal, Vol. 8(2), pp. 113-124, 2009.
  32. Foy, K., Wei, Z., Matsumura, T., and Huang, Y., ÒEffect of Tilt Angle on Cutting Regime Transition in Glass Micromilling,Ó Int. J. of Machine Tools and Manufacture, Vol. 49(3-4), pp. 315-324, 2009.
  33. Wang, X., Wang, W., Huang, Y., Nguyen, N., and Krishnakumar, K., ÒDesign of Neural Network-Based Estimator for Tool Wear Modeling in Hard Turning,Ó Journal of Intelligent Manufacturing, Vol. 19(4), pp. 383Ð396, 2008.
  34. Wang, W., Huang, Y., Grujicic, M., and Chrisey, D.B., ÒStudy of Impact-Induced Mechanical Effects in Cell Direct Writing Using Smooth Particle Hydrodynamic Method,Ó ASME J. of Manufacturing Sci. and Eng., Vol. 130(2), pp. 021012-1-10, 2008.
  35. Long, Y., Zhang, N., Huang, Y., and Wen, X., ÒFormation of Highly Aligned Grooves on Inner Surface of Semi-Permeable Hollow Fiber Membrane for Directional Axonal Outgrowth,Ó ASME J. of Manufacturing Sci. and Eng., Vol. 130(2), pp. 021011-1-8, 2008.
  36. Huang, Y., Chou, Y.K., and Liang, S.Y., ÒCBN Tool Wear in Hard Turning: A Survey on Research Progresses,Ó Int. J. of Advanced Manufacturing Technology, Vol. 35(5-6), pp. 443-453, 2007.
  37. Morehead, M., Huang, Y., and Luo, J., ÒChip Morphology Characterization and Modeling in Machining Hardened 52100 Steels,Ó Machining Science and Technology: An Int. Journal, Vol. 11(3), pp. 335-354, 2007.
  38. Tang, L., Wang, K.-C., Huang, Y., and Gu, F., ÒChannel Characterization and Link Quality Assessment of IEEE 802.15.4-Compliant Radio for Factory Environments,Ó IEEE Transactions on Industrial Informatics, Vol. 3(2), pp. 99-110, 2007.
  39. Huang, Y., and Liang, S.Y., ÒCutting Temperature Modeling based on Non-uniform Heat Intensity and Partition Ratio,Ó Machining Science and Technology: An Int. Journal, Vol. 9(3), pp. 301-323, 2005.
  40. Long, Y., and Huang, Y., ÒForce Modeling under Dead Metal Zone Effect in Orthogonal Cutting with Chamfered Tools,Ó Transactions of NAMRI/SME, Vol. 33, pp. 573-580, 2005.
  41. Huang, Y., and Liang, S.Y., ÒModeling of Cutting Forces under Hard Turning Conditions Considering Tool Wear Effect,Ó ASME J. of Manufacturing Sci. and Eng., Vol. 127(2), pp. 262-270, 2005.
  42. Huang, Y., and Dawson, T.G., ÒTool Crater Wear Depth Modeling in CBN Hard Turning,Ó Wear, Vol. 258(9), pp. 1455-1461, 2005.
  43. Huang, Y., and Liang, S.Y., ÒModeling of CBN Tool Crater Wear in Finish Hard Turning,Ó Int. J. of Advanced Manufacturing Technology, Vol. 24(9-10), pp. 632-639, 2004.
  44. Noh, H.S., Huang, Y., and Hesketh, P.J., ÒParylene Micromolding, a Rapid and Low-Cost Fabrication Method for Parylene Microchannel,Ó Sensors and Actuators B: Chemical, Vol. 102, pp. 78-85, 2004.
  45. Huang, Y., and Liang, S.Y., ÒEffect of Cutting Conditions on Tool Performance in CBN Hard Turning,Ó Transactions of NAMRI/SME, Vol. 32, pp. 511-518, 2004.
  46. Huang, Y., and Liang, S.Y., ÒEffect of Cutting Conditions on Tool Performance in CBN Hard Turning,Ó J. of Manufacturing Processes, Vol. 7(1), pp. 10-16, 2005.
  47. Huang, Y., and Liang, S.Y., ÒModeling of CBN Tool Flank Wear Progression in Finish Hard Turning,Ó ASME J. of Manufacturing Science and Engineering, Vol. 126(1), pp. 98-106, 2004.
  48. Tung, S.C., and Huang, Y., ÒModeling of Abrasive Wear in a Piston Ring and Engine Cylinder Bore System,Ó Tribology Transactions, Vol. 47(1), pp. 17-22, 2004.
  49. Huang, Y., and Liang, S.Y., ÒModeling of the Cutting Temperature Distribution under the Tool Flank Wear Effect,Ó Proc. Instn Mech. Engrs, Part C: J. of Mech. Eng. Science, Vol. 217(11), pp. 1195-1208, 2003.
  50. Huang, Y., and Liang, S.Y., ÒForce Modeling in Shallow Cuts with Large Negative Rake Angle and Large Nose Radius Tools Ð Application to Hard Turning,Ó Int. J. of Advanced Manufacturing Technology, Vol. 22(9-10), pp. 626-632, 2003.
  51. Huang, Y., and Liang, S.Y., ÒCutting Forces Modeling Considering the Effect of Tool Thermal Property Ð Application to CBN Hard Turning,Ó Int. J. of Machine Tools and Manufacture, Vol. 43(3), pp. 307-315, 2003.

Back to Top